Vizio Soundbars are a great way to amplify audio from an external device without purchasing a complete home theater system. If your Vizio Soundbar is not living up to your audio expectations, there are some easy solutions to this annoying problem.
The Vizio Soundbar can easily be reset by turning the power off for 10 seconds and then restarting. For a more in-depth problem-solving solution, simultaneously press and hold both the ‘Input’ and ‘Volume Up’ (+) buttons for 15 seconds.
If the Vizio Soundbar is not working correctly or not working at all, these issues can be resolved by resetting the soundbar. It only takes a few minutes and can save you a lot of money since these steps do not require you to hire a professional.
Is There A Reset Button On Vizio Soundbar
When it comes to resetting our electronic devices, a reset button would be great. With the press of one button, the problems are gone. Unfortunately, it doesn’t work that way and the Vizio Soundbar is no different.
The Vizio Soundbar does not have a stand-alone reset button. However, the soundbar does have a built-in reset feature. Pressing the correct sequence of buttons will activate this feature, resetting the soundbar and returning it to its original factory settings.
It is important to know how to reset your Vizio Soundbar. Electronic devices that are used frequently will develop glitches within the software that will affect the device’s ability to perform optimally. Resetting the soundbar will clear these glitches.
Power Surge
A power surge is exactly what it implies – a surge in electrical power. This surge can do great harm to our electronic devices, causing the soundbar to stop working or just not operate like it used to.
The surge in electricity can cause the soundbar to become stuck on a certain setting or command. Resetting the soundbar will refresh the software, waking it up, so it will respond to new commands.
How To Reset Vizio Soundbar To Factory Settings
As was just mentioned, resetting the soundbar is important in removing glitches within the soundbar’s software. These glitches can manifest themselves as an expensive problem – no sound, buzzing sounds, no power. You name it.
You can reset the Vizio Soundbar to factory settings by simultaneously pressing and holding both the ‘Bluetooth’ and ‘Down Volume’ (-) buttons for 15 seconds. All of the LED display lights will flash off and on three times. Once the lights stop flashing, the soundbar has been reset.
Performing a factory reset on your Vizio Soundbar will erase all saved preferences and settings. Once you have reset the soundbar, you will need to reconnect to the correct Wi-Fi network and go through the process of reconnecting your TV and other external devices to the soundbar.
Demo Mode
After performing a factory reset on the Vizio Soundbar you notice the soundbar dropping sound, Bluetooth is no longer visible, or only the volume buttons, the soundbar is in demo mode.
If you have the SmartCast Vizio Soundbar app downloaded, you can disable the demo mode from within the app. If you do not have the app downloaded, continue reading for two suggestions on how to disable the demo mode setting.
If you are only able to adjust the volume on the soundbar, press and hold both the ‘Input’ and ‘Bluetooth’ buttons for 10 seconds. All of the LED lights should flash 4 times. If the lights do not flash, you may be in a different demo mode setting.
If only USB content or content played through the Analog RCA output works, press and hold the ‘Input’ and ‘Volume Up’ (+) buttons for 10 seconds. The LED lights will flash four times. If the lights only flash once, repeat the steps.
How To Reset Vizio Soundbar Remote
The Vizio Soundbar remote does so much more than control the power or volume of the soundbar. You can use the remote to optimize and fine-tune the sound for different content and even individual audio settings.
You can reset the Vizio Soundbar remote by power cycling the remote. Remove the batteries from the remote. Press each button individually, two times. Replace the batteries with fresh batteries. Power on the remote.
If the Vizio Soundbar remote has been reset and powers on but the soundbar itself is not working correctly, you can use the remote to reset the soundbar.
Step 1: Using the remote, press the ‘Setup’ button.
Step 2: Select ‘Reset Audio’.
Step 3: Select ‘Audio Settings’.
Step 4: Press ‘OK’.
After step 4, all of the LED display lights will blink three times to indicate the soundbar has been reset. If the lights do not blink, repeat the steps one more time.
Copyright protected content owner: ReadyToDIY.com and was initially posted on 2022-01-03.
How To Reset Vizio Soundbar Without Remote
Using a remote does make life easier but if you do not have the remote for your Vizio Soundbar, you can still easily reset the soundbar.
You can reset the Vizio Soundbar without a remote by pressing and holding both the ‘Bluetooth’ and ‘Volume Down’ (-) buttons. Hold the buttons for 15 seconds or until all of the LED display lights stop flashing.
A Universal remote can easily be set up with your Vizio Soundbar. You will need the correct pairing code for your specific Vizio Soundbar. This code is brand-specific. You can easily find this code in your User’s Manual or online at Vizio.com.
Another cool feature of the Vizio Soundbar is its ability to communicate with your phone. If you purchased your Android phone within the last couple of years, the phone may have the capability of communicating with your soundbar. Check out the Playstore for Universal Remote apps.
How To Reset Vizio Soundbar Volume
Issues with the Vizio soundbar audio could be software issues. The best way to resolve this problem is to reset the soundbar. Resetting the soundbar will remove any glitches in the software and will force any pending updates.
Copyright article owner is ReadyToDiy.com for this article. This post was first published on 2022-01-03.
The Vizio Soundbar volume can be reset by turning on the DTS TruVolume feature. Using the Vizio remote, press the ‘Menu’ button. Select the ‘Audio’ menu and then navigate to ‘Volume Leveling’. Use the remote arrows to adjust the setting on or off.
If adjusting the DTS TruVolume settings did not resolve the issue. There are some other ways to troubleshoot the issue before resetting the soundbar. It is often best to start with the basics – make sure the volume on the soundbar is turned up.
Another suggestion is to make sure the soundbar is connected to the correct device.
Step 1: Turn on the TV.
Step 2: Press and hold the ‘Input’ button on the soundbar until the LED display lights all start flashing. The Soundbar is now searching to find the connected Audio source.
Verify The Source
Most audio issues with the Vizio soundbar have nothing to do with the soundbar itself. Oftentimes the issues come from the device the soundbar is connected to.
The best, and simplest, way to troubleshoot this issue is to connect the soundbar to another device. If the sound works, the issue is not with the soundbar.
Charging
If you power on the soundbar and the LED lights flash red, or there are no lights at all, the soundbar needs to charge.
Audio-Out Port
Make sure the soundbar is connected to the correct audio port connection on the TV. You want the audio from the TV to play out through the soundbar, which means the soundbar cable needs to be connected to the Audio-Out port.
TV Compatibility
Not all TVs are created equal. It is possible your TV is not designed to support the soundbar. Restarting the TV and checking the audio settings will help you determine if this is the real issue with the soundbar volume not working.
How To Reset Vizio Soundbar Wi-Fi
In this modern age, the life-blood of every household is the Wi-fi network. We depend on a good Wi-Fi signal to work, do school work, and stream movies for family night. The Vizio soundbar also relies on Wi-Fi.
You can reset the Vizio soundbar Wi-Fi by turning off the network router for 2 minutes. Restarting the router will help to improve the strength of the network’s signal to the soundbar. Once the router has been reset, make sure you are connected to the correct network.
One important reason to connect the Vizio Soundbar to a good Wi-Fi signal is so that the soundbar has the ability to receive software updates. These updates keep the soundbar working optimally.
If you notice the soundbar is not connecting to certain apps after resetting the Wi-FI, make sure all of the connecting cables are securely inserted into the correct ports. Restarting the soundbar itself will also help to remove this glitch.
How To Reset Vizio Soundbar Bluetooth
Bluetooth is a great way to connect our electronic devices. Connecting wireless saves us from having to connect a bunch of wires and then you have to worry about hiding all of those wires.
To reset the Vizio Soundbar Bluetooth settings, go to ‘Reset Audio’ settings and select ‘Reset All’. Press ‘OK’. The LED display lights will all blink three times to signal the soundbar has been reset. All paired Bluetooth devices will need to be connected to the soundbar again.
Related Articles
Vizio Soundbar No Sound
Vizio Soundbar Won’t Connect
Vizio Soundbar Not Working
Vizio Subwoofer Not Working
ReadyToDIY is the owner of this article. This post was published on 2022-01-03.
How To Connect Vizio Soundbar To Hisense/TCL/Roku TV
FAQs
How do I get my Vizio soundbar out of demo mode? ›
Press and Hold the Input and Bluetooth buttons for 10 seconds. All of the LEDs will flash four times. If the LEDs only flash once, repeat the steps above to disable the Demo Mode.
How do I factory reset my Vizio sound bar? ›- Press and hold the Bluetooth and Volume Down buttons simultaneously for five seconds.
- All 12 LEDs will flash three times.
- The factory reset is complete.
Turn ON your Vizio Soundbar by hitting the power button. Locate the Bluetooth and Volume Down buttons. Press these buttons and hold them simultaneously for approximately five seconds. Wait for all the lights on the soundbar to flash thrice before you let go.
How do you get a sound bar out of DEMO mode? ›You can disable DEMO mode by simultaneously pressing the INPUT and Power buttons on the unit for five seconds. Notes: You can also disable DEMO mode by simultaneously pressing the Power and VOL + buttons on the unit for five seconds. If you perform this method, it is recommend doing so with the sound off.
How do I get out of DEMO mode? ›- Select System — Retail mode settings — Set Demo mode and Picture reset mode to Off. ( Android™ 10 or later)
- Select Device Preferences — Retail mode settings — Set Demo mode and Picture reset mode to Off. ( ...
- Select Retail mode settings — Set Demo mode and Picture reset mode to Off. (
- Press and hold the (power) and - (volume down) buttons on the Soundbar for more than five seconds.
- Unplug the AC power cord.
- Plug the AC power cord back in, and press the (power) button to turn on the unit.
Using the VIZIO remote, press the Menu button. Use the Arrow buttons on the remote to highlight System and press OK. Highlight Reset & Admin and press OK. Highlight Reset TV to Factory Defaults and press OK.
How do I reset my soundbar without a remote? ›Turn off the soundbar and unplug it from the power outlet. Press and hold the “Reset” button on the back of the soundbar for at least 10 seconds. This button is usually located near the power cord. While continuing to hold the “Reset” button, plug the soundbar back into the power outlet.
How do I fix my Vizio sound bar? ›- Make sure your sound bar is powering on. ...
- Verify the sound bar is connected to an 'Audio Out' port on the back of the TV. ...
- Make sure the Sound Bar is set to the correct input. ...
- If you're still having trouble, try a 'factory reset' on the sound bar.
Unplug the power cord from the Sound Bar. Once unplugged, hold down the power button on the Sound Bar for 5 seconds. Reconnect the power cable, and try powering on your sound bar.
What are the codes for a Vizio sound bar? ›
- 31517.
- 11144.
- 32454.
- 31975.
- Press the Menu button on your VIZIO remote.
- Use the arrow keys to select System > Reset & Admin > Reset to Factory Settings.
- Once the Reset is complete follow the on screen setup instructions.
Most soundbar issues result from improper connection, an incorrect device setting, a poor physical arrangement. Most fixes are fairly simple, though some may require some time to troubleshoot.
How do I get sound only to come out of my soundbar? ›When an Optical Cable is connecting the TV and the Soundbar, simply change the Audio Settings to emit the sound via the Optical Output. This means that the sound will come from the Soundbar only, regardless of the TV volume level.
How do I restore my soundbar to my TV? ›Reset the soundbar by powering it off and then pressing and holding the Play/Pause button until it displays 'INIT OK'. Power on the soundbar, and then try pairing the soundbar to your TV again.
How do I turn off demo mode without remote? ›- Somewhere along the edge of the TV, there should be a “Menu” button, with a “+” and a “-“ button. ...
- Press the “Menu” button. ...
- Press the “Menu” button to select your option and use the “+” or “-“ buttons again to cycle through the On and Off settings.
It should be just under or on top of "About Phone". Scroll down until you find Demo Mode. Enable it, and you're finished!
What does demo mode do? ›Demo mode for the status bar allows you to force the status bar into a fixed state, useful for taking screenshots with a consistent status bar state, or testing different status icon permutations. Demo mode is available in recent versions of Android.
How do I reset my sound completely? ›- Check your audio and sound source. ...
- Go to sound settings. ...
- Check external speakers. ...
- Turn to a Windows troubleshooter. ...
- Go to sound settings to run troubleshooter in another way. ...
- In the sound settings screen, check the Volume mixer. ...
- Click the Reset button. ...
- Check the sound control panel.
To soft reset your Vizio sound bar, just unplug it from the wall, hold the Power button for 30 seconds, and plug it back in. To restore your Vizio soundbar to its original factory settings, press and hold the Bluetooth and Volume Down buttons for 5 seconds.
How do you factory reset your speaker? ›
On the back of your device, press and hold the microphone mute button for about 15 seconds. Your Google Home will let you know that it's resetting.
How do I reset my Vizio soundbar remote? ›To perform a Factory Reset, Press and Hold the Bluetooth( ) and Volume Down (—) buttons for 5 seconds. Note: This will erase all settings and preferences that you have set. Enable/disable the use of a VIZIO TV remote control to power on and adjust the volume of the sound bar.
Why is my soundbar on but no sound? ›When there is no sound from the soundbar, make sure the connected devices are turned on, the soundbar is set to the correct source, and the cable is connected properly.
Where is the VIZIO menu button? ›On a VIZIO remote, the menu button will either look like a gear wheel icon, or it have the word "MENU" printed on the button. To get TV channels using an antenna, you will need to connect the antenna to the TV first. Next you will need to change the input on the TV screen to the Antenna or TV input.
Can a VIZIO remote be Reset? ›You can reset a Vizio remote by power cycling the remote. Power cycling involves removing the remote's batteries and holding down the power button. If power cycling doesn't work, you may have to purchase a replacement remote.
What happens if I Reset my VIZIO TV to factory settings? ›Resetting a VIZIO Smart TV to its factory defaults will remove all customized settings, such as app, network, picture and audio settings, etc. The SmartCast platform with apps is found on VIZIO 4K UHD Smart TVs released between 2016 – 2017 and all VIZIO Smart TVs released since 2018.
How do I use my phone as a soundbar remote? ›To control your Soundbar with an iPhone, download the SmartThings app, then use the 'Source' button on the Soundbar itself or its remote to choose Bluetooth or WiFi. Both options will work. Add your device to the SmartThings app, and you're ready to go!
How do you put a soundbar in pairing mode without a remote? ›If you don't have the remote, press the Source button on the top panel and then select BT. After a few seconds, the panel will display BT READY if there is no Bluetooth device already connected to the soundbar. When BT READY appears, press and hold the Source button for more than 5 seconds until BT PAIRING displays.
How do I sync my soundbar with my TV remote? ›Setting up your TV's audio output will allow you to control the soundbar's volume using your remote. Once the output is set up, you can then choose to connect either a digital optical cable or an HDMI cable to the soundbar. After you do that, you'll be able to use one remote for both your TV and soundbar.
How long should a Vizio sound bar last? ›Soundbars: 6-16 years
A newer amplified soundbar, like a Sonos Arc, should not become obsolete anytime soon, though expect the hardware to operate for up to 7 years before needing a repair or a replacement.
Why is my sound bar not working on my TV? ›
Unplug the TV and soundbar for 10 seconds, and then plug them back in. Sometimes, reestablishing the HDMI “handshake” between the TV and the soundbar can fix minor malfunctions. 8. Update the firmware in the TV and soundbar, and then cycle the power.
How do I sync my Vizio soundbar to my TV? ›Connect one end of the HDMI cable to the HDMI 1 (ARC) port on the back of your TV. 2. Connect the other end to the HDMI OUT (ARC) port on your VIZIO Sound Bar.
How do I turn off DEMO mode without remote? ›- Somewhere along the edge of the TV, there should be a “Menu” button, with a “+” and a “-“ button. ...
- Press the “Menu” button. ...
- Press the “Menu” button to select your option and use the “+” or “-“ buttons again to cycle through the On and Off settings.
Reset the sound bar to the factory default settings. To perform a Factory Reset, Press and Hold the Bluetooth( ) and Volume Down (—) buttons for 5 seconds.
Why does my TV go to demo mode? ›The DEMO mode setting on the TV is used by retailers to display the functionality and features of the TV. Using this setting limits some of the features and functions commonly used in a home. The steps to disable the DEMO mode will differ depending on the design of the TV.
What is Demo mode in developer options? ›Enable Demo Mode lets you change the appearance of the status bar using adb demo mode commands. Or you can use Show Demo Mode to hide notifications and display a preset status bar. Note: The adb demo mode commands might not work on all devices because they are not verified during Android certification testing.